Forum clan ChPUshnikov

User info

Welcome, Guest! Please login or register.


You are here » Forum clan ChPUshnikov » Technology, trade » Glue, as replacing board vacuum table


Glue, as replacing board vacuum table

Posts 1 to 19 of 19

1

Hello!
In absence of a vacuum the table, sometimes problematic work with the subtle sheet details materials, the more if they large razmeraili contrary malenkie- such that mounting clips more than itself blasting the surface. Fastening on perimetru- not abolish from vibration in the center of the leaf (under big size).
In previous what arose idea use glue in as a capture the treated leaf and foundations (plywood, producing or the other tight sheet material used in as a podlozhki- foundations). Analogiya--formaldehyde resin have jewelers, on which fixed blasting detail.
Of course same glue should be osobyy- an ideal variant- glue as on a post-it. Holds well enough, not allows the walls are moving in, BUT allows very easily to separate up a blank from foundations. For lack banks with "glue from of stickers" in head climb ideas with kleysterom or than the similar.

That you think on this about? What options needed glue can be to apply?

0

2

sana wrote:

banks with "glue from of stickers"

Such type of glue is called syomnym (appealing), only in daunting his, perhaps, very hard find will.
I would better watched in side construction termokleev (this which in elements), the most cheap as times easily otkleivayutsya.

0

3

For small detalee the'm using bilateral didn, but there is minus to orgsteklu they may overdry dead-bolted, remain the remnants of glue which very hard to remove. But as termokley with Plexiglas? Who get him to say something?

0

4

The remnants of glue from scotch easily are cleaned today the-with some alcohol, on orgstekle (akrile and etc) traces not leaves

0

5

Bilateral didn (1-1,5mm) adds bumps in places fastening, and for delicate acrylic, or romarka- this already the distortion geometry leaf, especially under frezerovke-sample of households.

Incidentally on analogies with this theme, as on expense of to stowed, details on scheme:
commander- the gelva(or the other solubility in water glue) - leaf paper(desirable less tight, doughy) - the gelva- A piece
After obrabotki- fracture detail and basis with failure of leaf paper and not details. The remnants of continue to have.

As you such a idea?

0

6

sana wrote:

Двусторонний скотч (1-1,5мм) добавляет бугры в местах крепления, а для тонкого акрила или ромарка- это уже искривление геометрии листа, особенно при фрезеровке-выборке.

Кстати  по аналогии с этой темой, как на счет того чтоб крепить детали по схеме: 
Основа- ПВА(или другой водорастворимый клей)- лист бумаги(желательно менее плотный, рыхлый)- ПВА - Деталь
После обработки- разделяется деталь и основа с повреждением листа бумаги а не детали. остатки смыть.

Как вам такая идея?

При шелкографии применяют аэрозольный фиксатор в балонах, наносим на стол и потом спокойно клеим на него заготовку несколько раз, перестаёт клеить брызгаем ещё раз.

http://foto-land.ru/index.php?id=513

Last edited by Flint2015 (Jul 26 2015 16:14:03)

0

7

In-printing we use AM9, can cheaper will than 3M-OSx86
http://www.esaprint.ru/catalog/?SECTION_ID=1358#
Before used glue-spray T-Fix from companies Sericol, but AM8 grassroots more, yes and consumption less proved.

0

8

sana wrote:

Hello!
In absence of a vacuum the table, sometimes problematic work with the subtle sheet details materials, the more if they large razmeraili contrary malenkie- such that mounting clips more than itself blasting the surface. Fastening on perimetru- not abolish from vibration in the center of the leaf (under big size).
In previous what arose idea use glue in as a capture the treated leaf and foundations (plywood, producing or the other tight sheet material used in as a podlozhki- foundations). Analogiya- Elecon have jewelers, on which fixed blasting detail.
Of course same glue should be osobyy- an ideal variant- glue as on a post-it. Holds well enough, not allows the walls are moving in, BUT allows very easily to separate stocking from foundations. For lack banks with "glue from of stickers" in head climb ideas with kleysterom or than the similar.

That you think on this about? What options needed glue can be to apply?

Perhaps in this side think?
Have darkstona such, too, appeared.

0

9

And if for plastics use, antiskolzyaschie mats?

0

10

've been busted somewhere broadcast, where in as a fasteners tonkolistovogo of the material is been used the wax. Truth attempt to search any special binding voskov on the vastness of the internet not blocked success. Can be try ordinary wax, but to consist of working with until experimentation until not came close. :)

0

11

In its time was cutting dense color paper on CNC frezere. , with rubber cement to rezinovomu the mat glue BF6 (medical)

0

12

, with rubber cement templates MDF (not laminate) on bilateral didn, measuring 0.14 mm holds very well! Was photographing ready to products with the subtle edges you just hairdryer to not break the detail, from schoolchildren he razmyagchaetsya and this simplifies bifidobacteria.

0

13

The remnants of glue from scotches different highly well are cleaned platenklinom (is used under refuelling cartridges). 'm using regularly. Effect better, than from industrial alcohol.

0

14

As the, with rubber cement 2 billets glue Titibont (blue) through leaf A4. After processing couple of times did probably slam fist, a hammer details became disarticulated. The remnants of paper zater part. Think in your cases goes such option. Holds dead-bolted.

0

15

Strange, that this video here not yet guys have been posting:

And here is exactly and himself wax: https://shop.carbide3d.com/collections/ … turing-wax the price not the best drawer - 10 bucks for four ounces of (115 grams)
And here is he-same, but on more bozheskoy price: http://www.machinablewax.com/product.php?product=44 - one pound (450gramm) - 20 bucks.

0

16

Perhaps in this side think?
Have darkstona such, too, appeared.

Agree + blowers particles in gender stocking to table were to gain leverage over
Link
And if pity. Can be and very such a him do

0

17

Как-то покупал клей спрей для фиксации фотографий. Занимался стерео-варио открытками, клей использовал для приклейки линзы к фотографии. Есть клеи разной "мощности" фиксации. Самые дорогие это 3M, есть и дешевле. Поищите в инете

0

18

По мне, так клей для шелкографии самый оптимальный вариант. И держит нормально, и остатки легко удаляются.

0

19

Falcor wrote:

Такой тип клея называется съёмным (removable), только в розницу его, наверное, очень тяжело найти будет.
Я бы лучше смотрел в сторону строительных  термоклеев (это которые в стержнях), самые дешевые как раз легко отклеиваются.

спасибо, возьмем на заметку =)

0


You are here » Forum clan ChPUshnikov » Technology, trade » Glue, as replacing board vacuum table